Airlive POE-FSH808AT Manual do Utilizador

1 POE-FSH808AT 8-Port 48V Active POE + 2 Gigabit Uplink Web Smart Switch User’s Manual

2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 5 2 2. Installation of the Switch This chapter provides the detailed instructions

2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 6 2.2 Hardware Overview 2.2.1 Front Panel The front panel of the web smart switc

2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 7  Reset: The Reset button is to reset all the setting back to the factory defau

2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 8  The relative humidity in the location should not exceed 90% non-condensing hu

2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 9 Attaching the Switch to a 19-inch rack 2.5 Desktop Installation The POE-FSH808

2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 10 2.6 Cabling Requirements  For 100BASE-TX ports The 8 RJ-45 station ports req

2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 11 2.8 Reset to Default When you forgot your IP or password, please use the reset

3. Installation AirLive POE-FSH808AT User’s Manual 12 Before connecting any network device to POE-FSH808AT, you should take a few minutes to

4. Web Management AirLive POE-FSH808AT User’s Manual 13 The POE-FSH808AT can be configured by web based interface, including administra

4. Web Management AirLive POE-FSH808AT User’s Manual 14 The switch’s Default IP IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 Now if

Copyright and Disclaimer AirLive POE-FSH808AT User’s Manual i Copyright & Disclaimer No part of this publication may be reproduced

4. Web Management AirLive POE-FSH808AT User’s Manual 15 Step 4. Click on “Use the following IP address” button and enter the computer’s addr

4. Web Management AirLive POE-FSH808AT User’s Manual 16 If you have a fixed IP xDSL account or cable modem account, and there is no router in th

4. Web Management AirLive POE-FSH808AT User’s Manual 17 On the Switch  On the IP setting, set the gateway to Router’s LAN port address 192.

4. Web Management AirLive POE-FSH808AT User’s Manual 18 Menu Bar On the left side of the screen is the Menu bar where you and click to confi

4. Web Management AirLive POE-FSH808AT User’s Manual 19  Authentication Configuration  System IP Configuration  System Status  Load D

4. Web Management AirLive POE-FSH808AT User’s Manual 20 User can configure the IP settings, Subnet Mask, Gateway as below:  IP address: Man

4. Web Management AirLive POE-FSH808AT User’s Manual 21  MAC Address: Displays the unique hardware address assigned by manufacturer (defaul

4. Web Management AirLive POE-FSH808AT User’s Manual 22 After pressing Update button, the old web code will be erased. Then you can select the i

4. Web Management AirLive POE-FSH808AT User’s Manual 23  Tx/Rx-Ability: Enable or Disable. The default value is "Enable". Being

4. Web Management AirLive POE-FSH808AT User’s Manual 24  Current Status: Displays the status of each ports. This field indicates the port 9

Copyright and Disclaimer AirLive POE-FSH8PW User’s Manual ii FCC Statement Federal Communication Commission Interference Statement This equipm

4. Web Management AirLive POE-FSH808AT User’s Manual 25  Destination port: Theoretically it’s possible to set more than one destination por

4. Web Management AirLive POE-FSH808AT User’s Manual 26 Example: Type 5 for both Tx and Rx Rate and select the High as speed base for port 1 a

4. Web Management AirLive POE-FSH808AT User’s Manual 27 The broadcast packet is only checked at the selected port and the number of broadca

4. Web Management AirLive POE-FSH808AT User’s Manual 28  Port: The port number.  Enable: Enable PoE feature of the specific ports. The de

4. Web Management AirLive POE-FSH808AT User’s Manual 29 4.6.1 VLAN Mode You may select the VLAN Mode of the switch. Port-based VLAN is for

4. Web Management AirLive POE-FSH808AT User’s Manual 30  Don’t care: Don’t care means the outgoing packet of the selected port keep the origin

4. Web Management AirLive POE-FSH808AT User’s Manual 31 VLAN Member in Tag Based Mode In Tag Based Mode you need to define and configure you

4. Web Management AirLive POE-FSH808AT User’s Manual 32  VLAN Member Port Select: Select the VLAN Member here.  VID Source Port: This

4. Web Management AirLive POE-FSH808AT User’s Manual 33 After configured and selected, then click on Add to create the table and related port

4. Web Management AirLive POE-FSH808AT User’s Manual 34  Transmit packet & Receive packet: This category shows both the received packet

Table of Contents AirLive POE-FSH808AT User’s Manual iii Table of Contents 1. Introduction ...

4. Web Management AirLive POE-FSH808AT User’s Manual 35  Clear: Press “clear” will clear all counters.  Refresh: Press “Refresh” button

4. Web Management AirLive POE-FSH808AT User’s Manual 36 4.8.1 Priority Mode There are three priority modes available to specify the priority

4. Web Management AirLive POE-FSH808AT User’s Manual 37  =Enable High Priority. After Enabled High Priority, the following enabled Port Ba

4. Web Management AirLive POE-FSH808AT User’s Manual 38 The Class of Service for TCP/UDP port number allows the network administrator to assig

4. Web Management AirLive POE-FSH808AT User’s Manual 39 4.9 Security There are many management functions can be set or performed if you click

4. Web Management AirLive POE-FSH808AT User’s Manual 40  Read: Pull down the selection bar to choose a port number and click the read button t

4. Web Management AirLive POE-FSH808AT User’s Manual 41  Function Enable: To Enable or Disable the function.  Port Filtering Rule: The o

4. Web Management AirLive POE-FSH808AT User’s Manual 42  STP Mode: Disable, STP and RSTP. Select the STP version you want to enabled.  Bri

4. Web Management AirLive POE-FSH808AT User’s Manual 43 4.10.2 STP Port Settings The STP Port Setting page allows you to change the port p

4. Web Management AirLive POE-FSH808AT User’s Manual 44  Port No: The port ID. It cannot be changed. Aggregations mean any configured trunk

Table of Contents AirLive POE-FSH8PW User’s Manual iv 4.5.2 Port Mirroring ...

4. Web Management AirLive POE-FSH808AT User’s Manual 45  Loopback Detection Function: This column allows you to enable or disable Loopba

4. Web Management AirLive POE-FSH808AT User’s Manual 46 Traffic pattern on the network should be considered carefully before applying it. When a

4. Web Management AirLive POE-FSH808AT User’s Manual 47  Member: This column allows you to select the member Ports.  Status: This column

4. Web Management AirLive POE-FSH808AT User’s Manual 48 4.13 Miscellaneous Miscellaneous setting is used to configure output queue aging time,

4. Web Management AirLive POE-FSH808AT User’s Manual 49  Output Queue Aging Time:  Purpose: This function is used to avoid the traffic

4. Web Management AirLive POE-FSH808AT User’s Manual 50  VLAN Uplink:  Purpose: This switch does not implement Independent VLAN (IVL) MAC

Appendix A: Product Specifications AirLive POE-FSH808AT User’s Manual 51 A Appendix A: Product Specifications Standards IEEE 802.3 10BaseT

Appendix A: Product Specifications AirLive POE-FSH808AT User’s Manual 52 Led Indicators Per Port: Link/Act, PoE Act/Status Per Unit: Power Powe

Appendix: B: Troubleshooting AirLive POE-FSH808AT User’s Manual 53 This appendix contains specific information to help you identify and s

Appendix B: Troubleshooting AirLive POE-FSH808AT User’s Manual 54 Step3: The switch will reboot for 20 seconds and the configuration of switc

1. Introduction AirLive POE-FSH808AT User’s Manual 1 1 1. Introduction 1.1 Overview The POE-FSH808AT is a Power Control Active POE Switch. It w

1. Introduction AirLive POE-FSH808AT User’s Manual 2 * Note:  This switch does not work with passive PoE devices. It uses 802.3at/af PoE standard

1. Introduction AirLive POE-FSH808AT User’s Manual 3 1.4 Installation Steps This section lists the installation procedures in steps. Each step’s ins

1. Introduction AirLive POE-FSH808AT User’s Manual 4 Step8. If you want to install the switch on the 19" rack, please install the mounting